Contents. Linking Anope 1.8.x to InspIRCd 1.2 - 2.x Introduction This tutorial is written for Anope-1.8.4 and InspIRCd 2.0 This tutorial assumes that you've already configured InspIRCd to a basic level enabling it to at least run.

• Browse

1. Discussions about Anope that don't fit anywhere else. Discussions about Denora development and Module contributions. 57 Posts 11 Topics.
2. This module provides SSL services to Anope using GnuTLS, for example to connect to the uplink server(s). See for 3rd party modules. How to install a module.

You will probably have to make a few changes to link Anope to it. If you've previously linked Anope to another IRCd, eg. Unreal, the main differences you'll notice are mentions of TS6. InspIRCd uses the TS6 protocol which requires a few changes in the configuring of Anope.

Portal Home Knowledgebase IRCD Hosting How do I install Anope Services? To install Anope modules.

Nov 22, 2012 Intel(R) Graphics Media Accelerator 3600 Series WINDOWS XP driver I am using Hp mini 210-4127se. Downgrade from Windows 7 to XP. It hard finding the XP driver.

Note: This tutorial is NOT some step-by-step walkthrough for configuring Anope itself, it covers InspIRCd-specific issues you may encounter. The basic set-up of Anope should be done using the comments in the config with the supplied docs. InspIRCd Modules Required. Although Anope will start without this, you WILL need it for HostServ to actually set vHosts.

Enables global messages. For allowing support for usermode +I. Enables +r on identifying, as well as +R and +M channel modes.

The most important, without this services cannot link to InspIRCd, and any server bind blocks will be redundant. Suggested.

Enables aliases such as /NickServ, /ns rather then having to use /msg nickserv, you'll also need to uncomment the aliases. You'll need this if you use the 'recommended' UseSVSHOLD setting in services.conf. For extra channel modes eg.

Owner, Protected, Halfop, please read on. If using InspIRCd 1.2 you should use the following module:.

Enables +q and +a (Owner and Protected) If using 2.0.x the above module and halfop functionality have been replaced with the following:. Enables +q, +a, +h with the ability to change prefixes. Note that changing IRCd modules which add modes/commands will require services to be restarted to pick them up. Anope Configuration It is important at this point to make sure you have a new Anope-1.8.4 services.conf as it includes some extra information regarding TS6. Uncomment IRCDModule and set it to inspircd12 if using Anope-1.8.4, for Anope-1.8.5 you can use inspircd20.

Uncomment Numeric (the InspIRCd 1.2 compliant one). This numeric must be a TS6 ID, and conform to the following format: 0-9A-Z0-9A-Z0-9. 3AX will work. If you want to use svshold for holding nicks that have been 'Guest'd' by Nickserv, enable UseSVSHOLD. This should be used with msvshold loaded in inspircd. Uncomment UseTS6.

InspIRCd Configuration. Make sure you have a bind block in inspircd.conf, for servers. You cannot use the the same bind for servers and users. This bind shouldn't have SSL, as Anope 1.8.x doesn't support it, and won't link. Set a link block and Uline for Anope (links.conf). See below example.

README.md About Anope is an open source set of IRC Services. It is highly modular, with a vast number of configurable parameters, and is the most used IRC services package. There are also many modules on the to add additional features. It runs on Linux, BSD, and Windows, and supports many modern IRCds, including InspIRCd, UnrealIRCd, and ircd-hybrid.

Browse

For more details, credits, command line options, and contact information see. IRC #anope on irc.anope.org Installation Linux/BSD Download the latest release off of the. $./Config $ cd build $ make $ make install Now change to the directory where you installed Anope to, e.g. $ cd /services/ Windows Download the latest release off of the and run the installer. Configuration Copy conf/example.conf to conf/services.conf $ cp conf/example.conf conf/services.conf Edit services.conf, configuring the uplink, serverinfo, and protocol module configurations. Example link blocks for popular IRCds are included in the the example.conf documentation.

The is also a good source of information. Our support channel is located at #anope on irc.anope.org. Note that the example configuration file includes other example configuration files. If you want to modify the other example configuration files, copy them (e.g. Modules.example.conf to modules.conf) and modify the include directive in services.conf to include the new file. Running Run $./bin/services to start Anope.

If asked to provide logs for support, use the -support flag, e.g.: $./bin/services -support Installing extra modules Extra modules, which are usually modules which require extra libraries to use, such as mmysql, can be enabled with the./extras command from the source directory. Then re-run Config, make and make install again.

Third party modules can be installed by placing them into the modules/third directory.